VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  Starter Vape Kit standee cost guide
starter vape kits · B2B buyers

Starter Vape Kit standee cost guide

We work with B2B buyers who order between a few hundred and a few thousand units at a time, and we treat both ends the same way: a written specification, a sample you approve, and a production run that matches the sample.

Published 14 May 2026  ·  VapeWholesaleHub  ·  Reading time 5 min

Unit from the retained reference sample held against this order number.
Unit from the retained reference sample held against this order number.
Close inspection of the assembly line before the batch is released.
Close inspection of the assembly line before the batch is released.
Carton-ready units from the same batch, coded for traceability.
Carton-ready units from the same batch, coded for traceability.

Support that answers the question

Starter Vape Kit sits in a crowded price band, and the cheapest quote on the sheet is rarely the cheapest unit on your shelf. Everything below is built around reorder rate, defect rate and cash conversion rather than headline unit price.

The replacement policy is deliberately simple: report within seven days of delivery with photos and the batch code, and we replace or credit at the next shipment. We do not argue about a defect we can see in a photograph.

Technical questions usually arrive at the worst possible moment, which is why we answer them on WhatsApp as well as email. A photo and a two line message resolves most issues faster than a ticket.

The checks behind every shipment

A 0.5 percent defect rate sounds excellent until it lands on a 600 unit order and you are handling three returns in a week. We quote realistic rates per category and we credit in advance for the known failure modes.

Leak complaints almost always trace back to one of three things: an over-torqued centre post, a seal that sat in a hot container, or a fill volume pushed past the design limit. We cap fill volume slightly below maximum for exactly that reason.

For B2B buyers, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

Paperwork, labelling and market rules

If you sell into a market that requires child-resistant packaging, say so at quotation stage. Retrofitting a CR closure onto a finished bottle design usually means a new mould and a four week delay.

Regulation for starter vape kits differs by country and sometimes by state. We do not pretend to be your lawyer, but we do keep the document pack current and we will tell you when a configuration cannot legally enter a market you have named.

  • Reference sample retained from every batch
  • Batch codes traceable from carton back to production date
  • Consolidated or split shipping, quoted both ways
  • Seven-day defect reporting with replace-or-credit
  • Named account contact who has handled the product
  • Cartons drop-tested and pallet-counted for clean freight

Getting the carton there intact

For repeat buyers we hold a shipping schedule rather than shipping on request. A fixed weekly cut-off means your reorder lands before the shelf empties instead of after.

Transit times move with the season. Book space early for Q4 and around Chinese New Year, when factory output pauses for two to three weeks and freight rates tighten at the same time.

Specification summary

Typical specification for this category
Battery350 mAh
Pod capacity3.0 ml
Coil resistance0.8 ohm
IncludedDevice, pod, cable
ChargingUSB-C 5V/1A
PackagingBlister pack
Minimum order300 units per SKU, mixed cartons allowed
Lead time12 working days after artwork approval

We would rather lose an order at quotation stage than explain a mismatch after delivery, which is why the specification conversation comes before the price conversation.

Frequently asked

Do you support private label?

We do. Send your artwork or your brand direction and we will return a digital proof, then a physical dummy for colour approval. Packaging files stay on record so a rebrand later is a file update rather than a redesign.

How long does production take?

Around 12 working days after artwork approval for stock configurations, plus transit. Custom runs add roughly a week for tooling and a physical dummy. We confirm the date in writing on the order acknowledgement.

What happens if part of the order is defective?

Report within seven days with photos and the batch code. Confirmed defects are replaced or credited on the next shipment. The failure is logged by mode and batch, and reviewed monthly with the factory.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us