VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  Starter Vape Kit spare kit for vape shops guide
starter vape kits · B2B buyers

Starter Vape Kit spare kit for vape shops guide

This page is for B2B buyers who want a working answer on specification, price and lead time before they commit a purchase order. We have written the detail down so nobody has to sit through a sales call to extract it.

Published 08 October 2026  ·  VapeWholesaleHub  ·  Reading time 8 min

Bulk packing station during the run for a B2B buyers order.
Bulk packing station during the run for a B2B buyers order.
Close inspection of the assembly line before the batch is released.
Close inspection of the assembly line before the batch is released.

The reorder is the real test

We work with B2B buyers who order between a few hundred and a few thousand units at a time, and we treat both ends the same way: a written specification, a sample you approve, and a production run that matches the sample.

Returns are handled as data, not as complaints. Every reported failure is logged by mode and by batch, and the pattern is reviewed monthly with the factory.

For private label accounts we hold the artwork files and the approval record. Rebranding a line eighteen months later is then a file update instead of a redesign.

How we structure a first order

The first question we ask is not what you want to spend. It is what your customer already buys. Answer that and the starter vape kit list writes itself; skip it and you end up with a pallet of stock that photographs well and sells badly.

We keep a short list of approved configurations for starter vape kits. Anything outside that list is possible, but it becomes a custom run with a custom lead time, and we quote it as such rather than pretending everything is standard.

For B2B buyers, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

Getting the documents right

Artwork approval is a two stage process: a digital proof for text and layout, then a physical dummy for colour and finish. Skipping the dummy is the single most common cause of a reprint.

Regulation for starter vape kits differs by country and sometimes by state. We do not pretend to be your lawyer, but we do keep the document pack current and we will tell you when a configuration cannot legally enter a market you have named.

  • Cartons drop-tested and pallet-counted for clean freight
  • Artwork proof plus physical dummy for custom packaging
  • Specification locked in writing before production starts
  • Consolidated or split shipping, quoted both ways
  • Standing reorder schedule with a fixed cut-off
  • Batch codes traceable from carton back to production date

Where defects actually come from

Leak complaints almost always trace back to one of three things: an over-torqued centre post, a seal that sat in a hot container, or a fill volume pushed past the design limit. We cap fill volume slightly below maximum for exactly that reason.

We photograph the packing station during production for volume orders. It is a small thing, but it settles most arguments about what was actually in the carton before it was sealed.

Specification summary

Typical specification for this category
Battery500 mAh
Pod capacity2.0 ml
Coil resistance0.8 ohm
IncludedDevice, 2 pods, cable
ChargingUSB-C 5V/1A
PackagingBlister pack
Minimum order100 units per SKU, mixed cartons allowed
Lead time25 working days after artwork approval

If any of this is unclear, the fastest route is a message rather than a meeting. Send the market you sell into and the price band you work in, and you will get a specific answer instead of a brochure.

Frequently asked

Can we order samples before committing?

Yes. Sample orders are shipped by air express and the cost is credited against your first production order above 300 units. We would rather you handle the sample than approve a specification from a photograph.

How long does production take?

Around 28 working days after artwork approval for stock configurations, plus transit. Custom runs add roughly a week for tooling and a physical dummy. We confirm the date in writing on the order acknowledgement.

What is the minimum order for starter vape kit?

Standard configurations start at 300 units per SKU, with mixed SKUs allowed inside the same carton. Custom colours, custom packaging or a private label run usually start at 800 units because of setup time on the line.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us