VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  Starter Vape Kit factory audit checklist — a workbook
starter vape kits · B2B buyers

Starter Vape Kit factory audit checklist — a workbook

Starter Vape Kit sits in a crowded price band, and the cheapest quote on the sheet is rarely the cheapest unit on your shelf. Everything below is built around reorder rate, defect rate and cash conversion rather than headline unit price.

Published 17 March 2026  ·  VapeWholesaleHub  ·  Reading time 5 min

Close inspection of the assembly line before the batch is released.
Close inspection of the assembly line before the batch is released.
Surface finish under raking light, one of the cosmetic checks.
Surface finish under raking light, one of the cosmetic checks.

Getting the documents right

Buyers come to us for starter vape kit after a bad quarter: dead stock on one side, empty shelves on the other. The cause is usually the same, an assortment built from a catalogue instead of from sell-through data. This page explains how we rebuild that balance for B2B buyers.

If you sell into a market that requires child-resistant packaging, say so at quotation stage. Retrofitting a CR closure onto a finished bottle design usually means a new mould and a four week delay.

Labels are where good orders go wrong. Nicotine warnings, child-resistant closures, batch coding and market-specific text all have to be correct before the pallet leaves. We prepare test reports, declaration of conformity and safety data sheets for each shipment and we ask for your destination list early so artwork matches the market.

What we test before a carton is sealed

Battery safety is not a marketing line. Cells are matched by capacity and internal resistance before assembly, charging boards are checked for cut-off voltage, and any unit that fails the cut-off test never reaches packing.

We photograph the packing station during production for volume orders. It is a small thing, but it settles most arguments about what was actually in the carton before it was sealed.

For B2B buyers, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

How orders move from factory to shelf

Damage in transit is nearly always a packing decision, not bad luck. Double-walled cartons, internal dividers and a drop-tested configuration cost a little more and save the argument at the other end.

Documentation travels with the goods: commercial invoice, packing list, and the certificate set for your market. We send a scanned copy before dispatch so your broker can clear the file in advance.

  • Standing reorder schedule with a fixed cut-off
  • Document pack prepared per destination market
  • Cartons drop-tested and pallet-counted for clean freight
  • Mixed SKU cartons to spread first-order risk
  • Consolidated or split shipping, quoted both ways
  • Artwork proof plus physical dummy for custom packaging

Reading a quotation properly

Freight is quoted separately and honestly. Bundling it into the unit price looks tidy and hides the one line that changes most often between shipments.

We publish a realistic band of 2.71 to 9.03 per unit for standard configurations at 60 units. Below that band you are buying a lighter specification; above it you are paying for finish, packaging or a smaller run.

Specification summary

Typical specification for this category
Battery350 mAh
Pod capacity3.0 ml
Coil resistance0.8 ohm
IncludedDevice, 2 pods, cable
ChargingUSB-C 5V/1A
PackagingBlister pack
Minimum order50 units per SKU, mixed cartons allowed
Lead time22 working days after artwork approval

None of this is complicated. It is just written down, which is more than most buyers get before they wire a deposit.

Frequently asked

Can we order samples before committing?

Yes. Sample orders are shipped by air express and the cost is credited against your first production order above 60 units. We would rather you handle the sample than approve a specification from a photograph.

How do you handle repeat orders?

The specification is held on file against your account, so a reorder is a reference rather than a new brief. We recommend a standing schedule with a fixed weekly cut-off so stock lands before the shelf empties.

What is the minimum order for starter vape kit?

Standard configurations start at 60 units per SKU, with mixed SKUs allowed inside the same carton. Custom colours, custom packaging or a private label run usually start at 240 units because of setup time on the line.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us