VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  Starter Vape Kit disposal and recycling — a overview
starter vape kits · B2B buyers

Starter Vape Kit disposal and recycling — a overview

We ship starter vape kits to distributors, chain buyers and independent shops. What follows is the material we normally cover in a first conversation: what we hold in stock, how we test it, how it ships, and what happens when a carton arrives damaged.

Published 20 November 2025  ·  VapeWholesaleHub  ·  Reading time 7 min

Unit from the retained reference sample held against this order number.
Unit from the retained reference sample held against this order number.
Surface finish under raking light, one of the cosmetic checks.
Surface finish under raking light, one of the cosmetic checks.

Price breaks and payment terms

Buyers come to us for starter vape kit after a bad quarter: dead stock on one side, empty shelves on the other. The cause is usually the same, an assortment built from a catalogue instead of from sell-through data. This page explains how we rebuild that balance for B2B buyers.

Freight is quoted separately and honestly. Bundling it into the unit price looks tidy and hides the one line that changes most often between shipments.

We publish a realistic band of 2.72 to 9.03 per unit for standard configurations at 240 units. Below that band you are buying a lighter specification; above it you are paying for finish, packaging or a smaller run.

What a sensible opening order looks like

Sourcing trips still matter for volume buyers. Seeing the line, the ageing room and the packing station tells you in an hour what six emails cannot. We host visits by appointment and we do not stage them.

When you compare suppliers for starter vape kit, ask for the last three production dates on the same SKU. If the answers are vague, the specification is not being held and the next batch will not match the sample you approved.

For B2B buyers, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

How orders move from factory to shelf

Damage in transit is nearly always a packing decision, not bad luck. Double-walled cartons, internal dividers and a drop-tested configuration cost a little more and save the argument at the other end.

If you dropship, we can label cartons to your format and omit our documentation from the outer box. It is a small operational detail that decides whether your customer sees a supplier or a partner.

  • Private label files archived for future rebrands
  • Document pack prepared per destination market
  • Mixed SKU cartons to spread first-order risk
  • Reference sample retained from every batch
  • Seven-day defect reporting with replace-or-credit
  • Batch codes traceable from carton back to production date

What we test before a carton is sealed

Leak complaints almost always trace back to one of three things: an over-torqued centre post, a seal that sat in a hot container, or a fill volume pushed past the design limit. We cap fill volume slightly below maximum for exactly that reason.

Battery safety is not a marketing line. Cells are matched by capacity and internal resistance before assembly, charging boards are checked for cut-off voltage, and any unit that fails the cut-off test never reaches packing.

Specification summary

Typical specification for this category
Battery800 mAh
Pod capacity3.0 ml
Coil resistance0.8 ohm
IncludedDevice, pod, cable
ChargingUSB-C 5V/1A
PackagingBlister pack
Minimum order100 units per SKU, mixed cartons allowed
Lead time12 working days after artwork approval

The detail above is what we hold ourselves to on every shipment, including the small ones. It is also the list we will walk through with you before the first order.

Frequently asked

What happens if part of the order is defective?

Report within seven days with photos and the batch code. Confirmed defects are replaced or credited on the next shipment. The failure is logged by mode and batch, and reviewed monthly with the factory.

How long does production take?

Around 25 working days after artwork approval for stock configurations, plus transit. Custom runs add roughly a week for tooling and a physical dummy. We confirm the date in writing on the order acknowledgement.

What documents come with a shipment?

Commercial invoice, packing list, and the certificate pack for your market: test reports, declaration of conformity and safety data sheets. We send scans before dispatch so your broker can pre-clear the file.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us