VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  Starter Vape Kit AQL entry level guide
starter vape kits · B2B buyers

Starter Vape Kit AQL entry level guide

We ship starter vape kits to distributors, chain buyers and independent shops. What follows is the material we normally cover in a first conversation: what we hold in stock, how we test it, how it ships, and what happens when a carton arrives damaged.

Published 01 October 2026  ·  VapeWholesaleHub  ·  Reading time 9 min

Starter Vape Kit AQL entry level guide configuration from a production run, photographed before packing.
Starter Vape Kit AQL entry level guide configuration from a production run, photographed before packing.
Carton-ready units from the same batch, coded for traceability.
Carton-ready units from the same batch, coded for traceability.
Close inspection of the assembly line before the batch is released.
Close inspection of the assembly line before the batch is released.

Quality control, in plain terms

If you are comparing three quotes for starter vape kit, compare the paperwork first. Test reports, artwork files, batch coding and the replacement clause tell you more about a supplier than the unit price on page one.

We photograph the packing station during production for volume orders. It is a small thing, but it settles most arguments about what was actually in the carton before it was sealed.

Cosmetic grading is written down, not argued about. Minor scuffs inside the tolerance band are accepted; anything that would make a customer put the unit back on the shelf is rejected. Your staff should never have to explain a finish defect to a paying customer.

Getting the carton there intact

Damage in transit is nearly always a packing decision, not bad luck. Double-walled cartons, internal dividers and a drop-tested configuration cost a little more and save the argument at the other end.

We ship from Shenzhen and Guangzhou: air express for samples and part loads, sea freight for volume. Typical production lead time is 18 working days after artwork approval, plus transit. We quote both routes so you can see the trade-off instead of guessing at it.

For B2B buyers, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

Labels, closures and traceability

If you sell into a market that requires child-resistant packaging, say so at quotation stage. Retrofitting a CR closure onto a finished bottle design usually means a new mould and a four week delay.

Artwork approval is a two stage process: a digital proof for text and layout, then a physical dummy for colour and finish. Skipping the dummy is the single most common cause of a reprint.

  • Mixed SKU cartons to spread first-order risk
  • Consolidated or split shipping, quoted both ways
  • Artwork proof plus physical dummy for custom packaging
  • Cartons drop-tested and pallet-counted for clean freight
  • Document pack prepared per destination market
  • Reference sample retained from every batch

Choosing the core line

A practical starting order for B2B buyers is 50 units across two or three SKUs, not 50 units of one. That spreads the risk, gives your staff something to compare, and still hits the first price break.

Colour range is where assortments quietly die. Six finishes look impressive in a brochure and disastrous on a shelf with 40 cm of space. We recommend two finishes per core SKU and let the trial line carry the novelty.

Specification summary

Typical specification for this category
Battery350 mAh
Pod capacity2.5 ml
Coil resistance1.2 ohm
IncludedDevice, pod, cable
ChargingUSB-C 5V/1A
PackagingRetail box
Minimum order100 units per SKU, mixed cartons allowed
Lead time30 working days after artwork approval

We would rather lose an order at quotation stage than explain a mismatch after delivery, which is why the specification conversation comes before the price conversation.

Frequently asked

How do you handle repeat orders?

The specification is held on file against your account, so a reorder is a reference rather than a new brief. We recommend a standing schedule with a fixed weekly cut-off so stock lands before the shelf empties.

Do you support private label?

We do. Send your artwork or your brand direction and we will return a digital proof, then a physical dummy for colour approval. Packaging files stay on record so a rebrand later is a file update rather than a redesign.

Can we order samples before committing?

Yes. Sample orders are shipped by air express and the cost is credited against your first production order above 50 units. We would rather you handle the sample than approve a specification from a photograph.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us